21 Comments

  1. Thomas Davis
    June 12, 2019 @ 7:37 pm

    Hi im 14 and i do wood work any tips

    Reply

  2. Wooden Crowe
    June 12, 2019 @ 7:37 pm

    Nice gift idea! Love my CNC & Laser!

    Reply

  3. Mr. Uraxan
    June 12, 2019 @ 7:37 pm

    Wow nice…job

    Reply

  4. Michael Perez
    June 12, 2019 @ 7:37 pm

    Love the vertical grain! Hickory was a good choice

    Reply

  5. hoverluver
    June 12, 2019 @ 7:37 pm

    Cool. Nice job on the product placement. Keep up the good work. X-Carve vs Shapeoko ?  Why X-Carve both seem similar

    Reply

  6. Paul Stutzenstein
    June 12, 2019 @ 7:37 pm

    I never thought cutting 45s on a table saw could look so cool! Great video!

    Reply

  7. Esteban Almeida
    June 12, 2019 @ 7:37 pm

    That's a great project! Hope make some one soon! About the music, what's the songs in 0:23 to 0:50 and in 2:01 to 3:00? Excelent crafts and music on your channel!!!

    Reply

  8. MIke The Wood Worker
    June 12, 2019 @ 7:37 pm

    I bought your plans the other day, made this box successfully and I used a Forstner bit for my hole in the top.

    Reply

  9. Dave Erickson
    June 12, 2019 @ 7:37 pm

    It looks like we have the same band saw. Any tips on drift?

    Reply

  10. adam long
    June 12, 2019 @ 7:37 pm

    My motto for 2019: “Save the wood. Respect the walnut.”

    Reply

  11. JusBidniss
    June 12, 2019 @ 7:37 pm

    The worst thing to me about a box of tissues is that as they get used, they get further away from the hole, with the top one eventually falling down inside and away from the hole so you don't have the handy popup effect, requiring you to reach in and dig in that annoyingly dry stuff with your fingernails to find the edge of the next one. So I'd like to see (and make) a tissue box where you discard the cardboard box and put the stack of tissues into the wooden box. Make it with a fixed bottom, but get this: A top that is not attached, but which follows the stack down as they get used, so that the tissues are always right up against the hole, and the top one always sticking out and able to be easily grabbed. So a fixed bottom and a 'follower' top, and toss the original cardboard box. What do you think?

    Reply

  12. Joshua Francis
    June 12, 2019 @ 7:37 pm

    Love the contrast and finish on the walnut and hickory – Well done sir!

    Reply

  13. Router 58
    June 12, 2019 @ 7:37 pm

    Another good project but if you don't have a cnc just use an Oval Drill bit 🙂 Merry christmas

    Reply

  14. JewishBacon
    June 12, 2019 @ 7:37 pm

    Really like this, but was there no safer way to accomplish the 7:23 router maneuver? I feel like your fingers were SOO close to the bit.

    Reply

  15. Jim Rumsey
    June 12, 2019 @ 7:37 pm

    This would be a neat chicken feather dispenser.

    Reply

  16. Trent Stephens
    June 12, 2019 @ 7:37 pm

    Damn, I really wanted to be a troll about respect the walnut. But you shut me down before i had the chance.

    Reply

  17. Daniel Harpham Gist
    June 12, 2019 @ 7:37 pm

    Hi David, thanks for another great vid. I made one for a Christmas present.

    Reply

  18. Blake Weber
    June 12, 2019 @ 7:37 pm

    You really should have made a box to put your chicken feathers in.

    Reply

  19. Tim McAvoy
    June 12, 2019 @ 7:37 pm

    Do you like the X-Carve (would you recommend it)? I have been looking into the X-Carve and the Shapeoko. Are there any other entry level CNC machines you would recommend checking out?

    Reply

  20. PhunKiss Artistic Creations
    June 12, 2019 @ 7:37 pm

    "Respect the Walnut" we smiled. "Scrap Walnut you don't have to respect" We did a spit take!

    Reply

  21. Jason Wyliie
    June 12, 2019 @ 7:37 pm

    I’m a big fan of your channel and the work you do. Thank you for sharing your knowledge. I’m also here in the Buckeye state, Youngstown area.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *